Stainless Steel Gold Fan Shape Mosaic
Stainless Steel Exotic Gold Fan Shape Mosaic
Stainless Steel Gold Fan Shape Mosaic Dimension
Product image 1Stainless Steel Gold Fan Shape Mosaic
Product image 2Stainless Steel Exotic Gold Fan Shape Mosaic
Product image 3Stainless Steel Gold Fan Shape Mosaic Dimension

Stainless Steel Exotic Gold Fan Shape Mosaic

Regular price $88.15

Unit price per 

only -6 left in stock

Sold per sheet


Stainless Steel Exotic Gold Fan Shape Mosaic is brought to you by luxury Mosaic Tiles from Spain. This Mosaic is made up of metal pieces to create an intriguing look for walls in bathrooms or kitchens. The sheet size is 300x200mm this mosaic has a gloss finish.

Website prices are per sheet.

Sheet Size: 300x200 mm
Chip Size: 80x75 mm
Number of sheets per m2: 16.66

Please call us or visit our showroom to check stock availability

Technical Data:


The wall must be firm, levelled, dry and clean. Uneven surfaces greater than 2 mm must be levelled with specific products. All cracks and imperfections should be repaired, so that the wall is completely smooth. The moisture content of the surface must be under 2%.


For a correct installation, several factors must be taken into account: Material kind of the wall to be tiled (synthetic pannels, plaster, wood, etc.), wall stability, environmental conditions, kind of surface to be covered , speed of carrying the work, etc. All the above parameters determine the choice of the adhesive kind. We always recommends to test first the material with minimum two pieces before placing all the material. Make sure that the chosen adhesive is apt for the material to be installed.

    • Mosaics with ceramic support and metal coated: use C1 cement based, C2 cement based or epoxy adhesive. (Stainless Steel Exotic Gold Fan Shape Mosaic and Stainless Steel Exotic Rose Gold Fan Shape Mosaic)


We recommend starting the installation from the floor to the ceiling, continue in phase to allow the adhesive the necessary time to get dry. This will avoid vertical displacements. Extend a thin layer of adhesive on to the surface where the piece will be installed (3mm approx.) Then, use a notched trowel no. 3 to make incisions into the adhesive layer. Place the piece while the adhesive is still soft and before a dry layer of film forms on the adhesive surface. Once the piece is placed, press carefully to obtain a correct adhesion and to cover possible areas without adhesive. Important: make sure that the distance between one sheet and another is the same as the one among the components so that all the joints look alike. For irregular mosaics, we recommend pulling out some components and relocating them in the joint between two sheets. This will improve the finish of the mosaic.


All the metal mosaics can be cut using a metal radial disk. We recommend continuous rim disks.


All joints must be perfectly clean and dry and having a minimum depth of 2mm. Use a flat rubber trowel to spread the paste, being sure that the joints are completely covered. Use a wet sponge or neutral PH products ? never abrasive products ? to wash off immediately the excess of grouting paste from the surface before it dries.

For better waterproofing, we recommend an epoxy grouting paste, especially in water areas.

Important:The colour of the grouting paste might change the product?s appearance. We recommend to test with some pieces before grouting the entire surface. All the metal mosaics have a low resistance to scratching. For a proper finish, use a fine grouting material. Excess of grout must be immediately cleaned with a sponge and water, avoiding excessive pressure.

Be especially careful as it is at this stage of the installation when scratching is more frequent. Important: we recommend a test of grouting in one piece BEFORE grouting the whole surface.

Use a damp sponge and clean water to wash off the excess of grouting paste from the surface. It is very important to do this before the paste dries. If this happens, use a cement remover to clean the surface.(not apt for stone)


For everyday cleaning, use regular pH neutral cleaners. Do not use abrasive products.

For metal mosaics, use product for daily cleaning of metals. Never use rust cleaners because it alters the surface finish of the part.



Open tab

We work with the best delivery services available to ensure your products are safe and arrive at destination in the best condition.  

You can choose your delivery options at checkout. The cost will depend on your location and weight of the package. 

Your orders will arrive approximately 1 to 2 weeks from placing your order. This time frame could be altered based on your location and weight of your package.

If you have any questions about delivery please contact us.

Close (esc)

Offers and discounts

Sign up to our email list now and get exclusive offers and discounts. We won't send you spam emails, just good stuff.

Age verification

By clicking enter you are verifying that you are old enough to consume alcohol.


Shopping Cart

Your cart is currently empty.
Shop now